My wide range of experience & expertise in many phases of electronics, communications and computer networking; Design, manufacture, installation, maintenance, trouble shooting, system wide & component level repair give me abilities and insights few others can lay clam to. On large equipment buys, build outs and upgrades I can act as an consultant giving you direct access to our tier one suppliers for direct shipping of equipment to your site.
If you have an application you want to run I can work with your software vender to design, build, configure and support a system and platform that will easily run your application and get you the best price on the equipment you need to do it. You give me a set of prints and an equipment requirements and specifications list from your vender and I will give you back a fully operational system capable of running any application you need. That’s what I do!
It’s not afraid to get dirty, Hands on, Boots on the ground Onsite repair, service & support until the job is done!!
Most equipment repairs are done on a flat labor rate basis. Repairs that these flat rates do not apply to are done on an
estimate basis. I will examine the equipment and call you with an estimate for repair.
Flat labor rates DO NOT INCLUDE PARTS, Labor quotes are always plus parts you may set any parts cost limit you wish if you do not set any parts limit I place a default value of $25.00 on the parts limit. That is to say that if the parts to repair your equipment should run over $25.00 I will call you first and get your approval and possibly a deposit on more expensive items before ordering parts.
Labor rates are set based on amount of time for, and the complexity of the repair and are as follows
$50.00 plus parts for simple repairs taking less than half an hour
$75.00 to $175.00 plus parts This is the average rate for most equipment repairs taking more than one half
hour but less than two or three hours
$75.00 plus parts is charged for basic service calls and repairs were I come out and repair in one trip taking less than one and one half hours. If I have to pick up your equipment, return it to the shop, repair it and return it to you or the on site repair takes more than one and a half hours than a rate of $125.00 to $ 175.00 plus parts applies.
I charge a $25.00 to $50.00 diagnostic fee for equipment worked on but not repaired
Unless otherwise agreed to equipment will only be held for a period of 90 day after work has been completed.
If no other agreement has been made that equipment will be sold to cover repair cost and storage fees.
It is your responsibility to stay advised of the Statius of your equipment
All on site service and support for Business, Medical and Point of sale clients is billed at a rate of $75.00 an hour with an hour minimum unless otherwise agreed to in writing or by service contract.
A fee may also be charged for estimates and consulting.
Payment is due at the completion of service or at the time of equipment pickup. If you pay by personal or out of town check I may reserve the right to hold the equipment until your check clears. At this time I accept cash, company check on a Florida bank, personal check on a local bank, Pay Pal, Visa, MasterCard & Discover
Pro Electronics is always looking to buy Ham Radio equipment & Parts such as vacuum tubes and component parts,
Test equipment, Vintage & Contemporary Stereo, Audio & Sound equipment, Guitars and Amps.
I buy estates, sellout lots & single peaces. I buy this equipment for parts & resale.
I determine my paying price by looking at completed sales & auctions for your type of equipment to determine the
current resale price and demand for your equipment. I look at the age, physical and working condition of the
equipment and what I will have to put in to it to repair, restore & clean up the equipment too get it into good
selling condition . I pay 50% of what I believe I can resell the equipment for, the poorer the condition and the older
the equipment the less I will offer. I offer this service for those that don’t have the time or want the hassle of selling
the equipment them selves, however if you want top dollar selling it yourself is what you will have to do.
With my service all you do is cash the check and I do all the work that’s why I only pay 50%.
Please call if you have any questions I can also help you determine the current value of your equipment.
Repair and Service Fees and Billing Policies
Buy—Sell—Trade Used and Vintage Equipment
<"a href="Page600.htm">Previous Page